Q-See QT528 Uživatelský manuál stáhnout pdf (Strana 45)

88 89

CHAPTER 9 HARD DISK DRIVE

Server List

This allows you to add, delete or modify the DVR connection or connections if you are

remotely monitoring multiple systems.

Add – Add a DVR’s IP address or DDNS

domain name

Modify – Modify a DVR’s IP address or

DDNS domain name

Delete – Remove a DVR’s IP address or

DDNS domain name

Settings

Conﬁgure which alarms will activate and what will trigger them.

PICTURE 8-58

PICTURE 8-59

PICTURE 8-60

Alarm Type – Choose which alarm types you

want to be notiﬁed about.

Alarm Output Type – Choose whether the

phone alerts you with an audio or vibratory

alarm or a combination of both.

Information View

This presents information on the cell phone you are using the SuperCam software version on

as well as the software itself.

Device ID: This is the ID of the DVR you are

connected to. This can be set on the DVR in

the System tab shown in SECTION 4.1

Software Version: The current connection

device software version

Build Date: The date the software was

released

Software Version: The current version of the

BlackBerry software in use on your phone

Software Build Date: The date this version

of BlackBerry was released

HARD DISK DRIVE

CHAPTER 9

Your DVR uses a standard SATA (Serial Advanced Technology Attachment) hard disk drive and will support

a pair of drives up to 2TB (terabytes) each. These drives are the current industry standard and may be

purchased wherever computer parts are sold. Depending on where you purchased your DVR, it may come

with a pre-installed drive. But, we recognize that you may wish to upgrade or replace your drive in the future

so this DVR is designed to make installation and replacement easy for the average user.

It should be noted that while this is the only user-serviceable part within the case and you will not void your

warranty by installing or upgrading your hard disk drive, care must be taken to avoid damage to the other

components within the case.

VGA

SPOT

DC 12V

VIDEO OUT

1 3 5 7

42 6 8

USB

NET

AUDIO OUT

AUDIO IN

P/Z

Y Z A 1 3 5 7

2 4 6 8

RS485

ALARM OUT

ALARM

VIDEO

K/B

GND

COM

Remove Screws

9.1 INSTALLATION/REMOVAL

It is strongly advised against opening the case when atmospheric conditions present the risk of static

discharge which can damage electronic components.

Whether installing the drive for the ﬁrst time or removing the old one to install a new one, the steps are

largely the same:

STEP 1. Disconnect the DVR from the power source as well as any other connections.

STEP 2. Remove ten screws as indicated in Picture 9-1

WARNING! ELECTRIC SHOCK RISK!

The DVR MUST be unplugged from all power sources as well

as from the cameras before opening the case. Failure to do so

can result in damage to the DVR or its components as well as

injury or death.

PICTURE 9-1

PICTURE 9-2

STEP 3

. Remove the case by sliding it backwards and then lifting off.

STEP 3A. If removing a hard drive, you will

need to unscrew the four drive mounting

screws at the bottom of the DVR.

Holes for Mounting Screws

for Hard Disk Drives

Holes for Mounting Screws

for Hard Disk Drives

Holes for Mounting Screws

for Hard Disk Drives

1 2 ... 40 41 42 43 44 45 46 47 48 49 50

Komentáře k této Příručce

Žádné komentáře

Q-See QT528 Uživatelský manuál Strana 45

Komentáře k této Příručce

Související produkty a manuály pro Digitální videorekordéry (DVR) Q-See QT528